![]() ![]() The resolution seems overkill, with Full HD being kinder to the battery, not to mention cheaper. The AMOLED display has a layer of Corning Gorilla Glass 3 on top, and offers a resolution of 2,160 x 1,080 pixels spread over a 6.01-inch diagonal. There’s not much to shout about when it comes to the rest of the hardware. In the latter scenario, you will enjoy an almost cinematic experience if paired with a Bluetooth surround sound system.īlackview has also thrown in a stand that can hold the projector on a flat surface to provide an even better viewing experience. Overall, the projector’s performance was quite impressive, especially if you can somehow manage to use a white wall in a dark room. We also tried the Max 1 in a brightly lit room (with fluorescent lights) and with the projector placed 35cm from an improvised A4 sheet used as a screen. Geekbench: 908 (single-core) 4,023 (multi-core) 3,065 (compute)Īndrobench (sequential): 286 (sequential read) 198 (sequential write)Īndrobench (random): 61 (random read) 12 (random write) Here’s how the Blackview Max 1 performed in our suite of benchmark tests: In the first scenario, the colors were bright and the picture sharp, and the projector had no problems keeping up with fast moving movie footage. Just be careful with drops and knocks as MEMS are mechanical parts and could be damaged during falls on hard surfaces.ĭuring our brief encounter with the Max 1, it was evident that this projector will deliver its full potential in a dark room, or failing that, very close to a white surface in a brightly lit room. ![]() This is a 720p projector with a brightness of 50 Lumens, autofocus, auto keystone correction, and up to five hours playback. The unique selling point of this phone is its projector, of course, and it’s probably the same model as the one in the Voga V – which is from Microvision and is known as the MEMS-based PicoP PSE-0403-103. There’s a card from the founder and CEO of Blackview, Xu Ming (that’s a first), a remote control (handy for presentations), a manual for the Blackview BV9700 Pro (clearly a mistake), a microUSB converter, the charger, two USB cables, a Bluetooth speaker, a pair of Type-C earphones, a stand that doubles as a selfie stick (more on that later) and the aforementioned rubber case – all of which is housed in a big gift box. Unlike the Voga V, Blackview has bundled a few accessories with the Max 1. If the projection is blurry, focus it by moving the phone holder either backwards or forwards.CPU: Mediatek Helio P23 MTK6763T octa-core.Enter a dark room and play your photo, video, or movie.Now, insert your phone holder into the projector body (making sure that the photo, video, or movie is still upside down).On that same screen, make sure your phone is at its highest setting.To lock your screen, (on a IOS device) swipe up from the bottom edge of the phone and click the Portrait Orientation Lock and if it is on, it should turn red-orange.(The photo, video, or movie should flip its view) Hold the phone holder with the phone attached to it, upside down.Open the video, photo, or movie that you want to project.(Try to tape down the edges of the phone to the holder) Tape your phone down at the center of the holder.Take your phone holder and lay it down on a flat surface.Now that you have completed the body of the projector, and the phone holder that goes into it, it is time to use it! Make sure the two rectangles together, form a right angle when looking at it from the side.Take your hot glue gun and attach the two rectangles, the longest sides touching each other.Cut the rectangles out by following the outline of the rectangles that you have drawn.(My rectangle was 2 inches by 6 3/8 inches) This will be your height for the bottom support. To make the bottom support for the phone holder, use the measurement of the width, and for the height of the rectangle, divide the height of your back support rectangle by 2.(I decided to shorten (My rectangle was 4 inches by 6 3/8 inches) To make the back support for the phone holder, use your height and width to make a rectangle.(The height of the box was 4 3/4 inches, but I chose to make the height of the phone holder 4 inches) (Make sure to write your measurement on a piece of paper so that you may remember the measurements when making this with the cardboard) This time, using the ruler, measure the height of your rectangular box.(The width of mine is 6 3/8 inches) (Make sure to write this down on a piece of paper so that you may remember the measurements when making this with the cardboard) Take your ruler and measure the width of your rectangular box. ![]()
0 Comments
Leave a Reply. |